Shop vacuums, dust extractors, track saws, sanders and table saws almost never share the same hose or port size. Every woodworker ends up with a drawer full of adapters that almost fit. So I built a tool that makes the exact one you need.

Open the Vacuum Adapter Generator →

Pick your hose size, pick your saw’s port size, and the tool builds a 3D-printable adapter with a slightly tapered press-on fit that seals without clamps or tape. It’s free, and it runs entirely in your browser. Nothing is uploaded.

You can also watch the video where I show how to build the original design in Fusion: watch it on YouTube.

How to use it

  1. Measure both connections with calipers (see below).
  2. Choose a size for your saw or tool port and your vacuum hose, from the standard-size list or by typing an exact diameter. Type in inches or millimetres, and the other box converts automatically.
  3. Pick how each end connects. The default is the recommended setup (see below). The diagram on the page shows exactly which piece slides into which.
  4. Toggle the 90° turn if you need an elbow. This is handy where a hose would otherwise kink against a wall or workbench.
  5. Check the preview. Use the cross-section view to inspect the walls and taper, then download the STL and slice it in your usual slicer.

How to measure

  • Plugging inside a hose or port: measure the inside diameter of that opening. The adapter’s outer surface will press against it.
  • Sliding over a hose or port: measure the outside diameter of the part that goes into the adapter. The adapter’s inner surface will grip it.
  • Measure at the point where the adapter will actually sit, in two directions 90° apart. Flexible hose and molded plastic ports are often slightly oval.
  • Nominal sizes are only a starting point. A “2-1/2 inch” hose from one brand can be a millimetre or two different from another.

Air and dust flow from the saw, through the adapter, into the hose. The best way to join them is to slide the upstream piece into the downstream piece at every joint:

  • The saw port slides into the adapter.
  • The adapter presses into the hose.

That way every edge faces the same direction the air is moving, so chips and dust sweep past it. If it’s done the other way around, the edge of the inner piece faces into the airflow and creates a ledge where debris can catch and build up, which is how hoses clog. The tool uses this arrangement by default and warns you if you switch it.

Which end should be male and which female?

A good rule of thumb: let the rigid part decide. Flexible hose can stretch over a male adapter end, or be squeezed into a female one, so it forgives small errors. Rigid saw ports don’t, so measure those most carefully. If a port has a molded lip or ridge, choose the side that doesn’t cross it.

Keep airflow in mind, too. A male end that goes inside a small port narrows the opening, so a female end over the outside of the port gives you a larger bore.

How the tapered press fit works

Each connection is a shallow cone rather than a straight tube. The diameter you enter sits in the middle of the taper. The tip of the adapter is a little smaller (male) or a little larger (female) so it starts easily, and the diameter closes in along the engagement length until it presses firmly. The default is 1 mm of total diameter change over 40 mm, which is gentle enough to push on by hand and pull off again, but tight enough to hold under suction.

  • Engagement length (default 40 mm): how far the hose or port slides on. Longer gives a stronger, better-sealed joint.
  • Wall thickness (default 2 mm): thicker is stronger but reduces the bore.
  • Taper (default 1 mm): the diameter change across the engagement. More taper is easier to start but grips on less length.
  • Fit adjust (default 0 mm): positive loosens the whole fit, negative tightens it.

Printing tips

  • Material: PETG is a good all-round choice: tough, a little flexible, and it handles a warm garage. PLA works indoors but can crack or warp if left in a hot car or shop. ABS or ASA is best for heavy-duty use.
  • Strength: use 3 to 4 perimeters. The part is mostly walls, so infill matters very little.
  • Orientation: print with the hose end flat on the bed. For the 90° version, use supports, or try tilting the part so the bend sits at about 45°.
  • Layer height: 0.2 mm is fine. Printing the outer wall slowly gives a smoother surface for sealing.
  • Test first: print only a short test ring with your settings before committing hours to a full adapter. Printers vary by a few tenths of a millimetre.

Troubleshooting

The adapter is too tight to push on. Set Fit adjust to +0.1 or +0.2 mm and reprint. Make sure you measured the correct dimension (inside versus outside) and removed any first-layer flare from the bottom edge.

The adapter is loose or leaks. Set Fit adjust to −0.1 or −0.2 mm, or increase the taper. A wrap of foil tape or a thin rubber band around a male end is a quick fix.

The adapter cracks along the layer lines. Increase the wall thickness, print hotter with slower cooling, or switch to PETG or ABS/ASA. Layer lines run around the part, so a hose being pulled sideways puts stress across them.

Suction is weak after adding the adapter. Check the bore dimensions shown in the tool. A much smaller bore than your hose restricts airflow. Prefer a larger-bore connection, a shorter transition, and a straight adapter over an elbow when you can.

Can I use this with hot, flammable or wet material? These adapters are designed for dry wood dust and light shop debris. Don’t use them for hot or flammable material, and keep them away from sparks such as grinders.

Try it

Open the Vacuum Adapter Generator →

If it saved you a trip to the hardware store, or you hit a size that doesn’t work, let me know in the comments on the video.

The tool is free. If it helped and you want to say thanks, you can buy me a coffee on Ko-fi.

— Corey Deaton